Teledyne 300m Instrukcja Użytkownika Strona 15
- Strona / 123
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Teledyne API Model 300M CO Analyzer Instruction Manual, 04033, Rev. A
CAUTION
Check that analyzer is set up for proper voltage and frequency.
CAUTION
Power plug must have ground lug.
7. Turn on the M300M by switching the switch on the lower right corner of the front panel (See
Figure 2-1). The front panel display should light with a sequence of messages, -API -
M300M - software version number, then a normal display as shown in Figure 2-2.
8. Allow about 30 minutes for the temperatures to come up to their respective set-points, then
press the left most button on the front keyboard to scroll through the TEST values. Compare
these values to those noted during the final factory checkout listed in Table 1-2. The values
observed should closely match the Table 1-2 values.
9. Select the range on which the analyzer will be calibrated.
A. From the SAMPLE menu, press SETUP to enter the SETUP menu. (See Figure 2-2 for
appearance of front panel.)
B. Enter the PASSWORD (818).
C. Press RNGE (RANGE).
D. Press SET.
E. Enter the derived full scale range for analog outputs and press ENTR.
F. Press EXIT 2 times to return to the SAMPLE menu.
10. Adjust the analyzer zero point.
A. Input zero air into the sample port.
B. Press CAL from the SAMPLE menu and enter the password (818).
C. Press ZERO.
D. It usually takes about 5 to 10 minutes for the reading to stabilize near zero. After a stable
reading has been obtained press ENTR. The display should now read 0.0 PPM Carbon
Monoxide.
1-7
- MODEL 300M 1
- CARBON MONOXIDE ANALYZER 1
- SAFETY MESSAGES 2
- TABLE OF CONTENTS 3
- LIST OF FIGURES 7
- LIST OF TABLES 8
- 1 INTRODUCTION 9
- 1.3 Principle of Operation 11
- 1.4 Specifications 13
- 1.6.4 RS-232 20
- 1.6.5 Pneumatic System 20
- 1.6.8 Exhaust Connections 21
- 1.7 Operation Verification 23
- 1.8 Options 25
- 2 OPERATION 27
- 2.1.6 RS-232 Interface 28
- 2.1.7 Password Protection 28
- 2.2 Front Panel 29
- 2.2.3 Status LED’s 34
- Table 2-5: Status LED’s 35
- 3 PERFORMANCE TESTING 37
- 3.1.2 Span Check 38
- 3.2 Span Valve (Option) 40
- Controls 44
- (Contact Closure) 45
- 3.8 Power-On Hold Off 46
- 3.9 Hold Off 46
- 4 SETUP MODE 47
- 4.3 Setting the Time-of-Day 48
- 4.4 Setting the Date 48
- 4.11.1 Data Channels 51
- 4.12 Software Configuration 52
- 4.13 Gas Alarms 53
- Table 4-1: Setup Functions 54
- 5 DIAGNOSTICS 57
- 5.2 Diagnostic Tests 58
- 5.2.1 Signal I/O 59
- (table continued) 60
- 5.2.2 Analog Output Test 62
- 5.2.3 Electric Test 62
- 6 HANDLING WARNINGS 65
- 7 RS-232 COMMUNICATIONS 67
- 7.1 DAS Reporting 68
- 7.2 Warnings 70
- 7.3 Status/Control 72
- 7.4 Diagnostics 74
- 7.5 Test Measurements 75
- 8 CALIBRATION 79
- 8.2 Multi-Point Calibration 81
- 8.2.1 Procedure 82
- 8.3 Zero/Span Checking 85
- 9 ADJUSTMENTS 87
- 9.5 Flow Readout Adjustment 92
- 9.6 DC Power Supply 93
- 9.7 CPU 93
- 10 TROUBLESHOOTING 95
- Components 102
- DAC Channel Signal 107
- 0 Strip Chart Analog Output 107
- 1 DAS Analog Output 107
- 2 Spare 107
- 10.6.7 Flow/Pressure Sensor 111
- 11 ROUTINE MAINTENANCE 113
- 11.3 Leak Checking 114
- 11.3.2 Leak Self Test 115
- INTENTIONALLY BLANK 116
- 12 SPARE PARTS LISTS 117
- Connectors: 120
- 4 general types 120
- Wiring: 121
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Teledyne 300m
(30 strony)
(42 strony)Trust 17389 manuals
Owner’s manuals and user’s guides for Mice Trust 17389.
We providing 1 pdf manuals Trust 17389 for download free by document types: Datasheet
Komentarze do niniejszej Instrukcji