Teledyne 300EU Instrukcja Użytkownika Strona 19
- Strona / 94
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
M300EU GETTING STARTED
(Addendum to M300EU Manual - P/N 04145)
3.5. INITIAL CALIBRATION
3.5.1. PRE-CALIBRATION STABILIZATION
Before initially calibrating the M300EU it must be allowed to operate for a minimum of 12 hours.
After this stabilization period is complete and just prior to performing the initial calibration, manually initiate an
auto-reference measurement by following the instructions in Section 6.4.
3.5.2. BASIC CO CALIBRATION SETUP
NOTE
The following procedure assumes that the instrument does not have any of the available Zero/Span
Valve Options installed.
To perform the following calibration you must have sources for zero air and span gas available for input into the
sample port on the back of the analyzer. See Section 3.1.3 of the M300E/EM Operators Manual (P/N 04288) for
instructions for connecting these gas sources.
NOTE
All Gas lines should be PTFE (Teflon), FEP, glass, stainless steel or brass
3.5.2.1. Calibration Gases
The information found in Section 3.1.3.2 of the M300E/EM Operators Manual (P/N 04288) is applicable to the
M300EU with the following exception:
ZERO AIR
A gas that is similar in chemical composition to the earth’s atmosphere but scrubbed of all components
that might affect the analyzers readings, in this case CO and water vapor.
For the M300EU this gas MUST include at least 5% O
2
(required for the proper operation of the
analyzer’s CO scrubber).
For analyzers without an IZS or external zero air scrubber option, a zero air generator such as the
Teledyne Instruments Model 701 can be used.
NOTE
The zero air generator MUST be equipped with a hydrocarbon (HC) & CO scrubber option.
For the Teledyne Instruments M701, this is Option 2B
05514 Rev A1 11
- MODEL 300EU 1
- SAFETY MESSAGES 3
- TABLE OF CONTENTS 5
- LIST OF FIGURES 6
- LIST OF TABLES 6
- LIST OF APPENDICES 7
- INTRODUCTION 9
- USER NOTES: 10
- WARRANTY 11
- GETTING STARTED 13
- 3.3. ELECTRICAL CONNECTIONS 14
- M300EU GETTING STARTED 15
- M300EU 16
- 3.4.2. WARNING MESSAGES 17
- 3.4.3. FUNCTIONAL CHECK 18
- 3.5. INITIAL CALIBRATION 19
- Scrubber 25
- SAMPLE CHAMBER 25
- 6.2. OPERATING MODES 28
- Mode Field 29
- 6.2.2. TEST FUNCTIONS 30
- RANGE CONFIGURATION 31
- FOR SINGLE RANGE MODE 33
- FOR DUAL RANGE MODE 34
- FOR AUTO RANGE MODE 35
- 05514 Rev A1 31 39
- DIAGNOSTICS FUNCTIONS 41
- AIO Configuration Submenu 43
- 6.7.4. HESSEN PROTOCOL 47
- CALIBRATION PROCEDURES 49
- EPA PROTOCOL CALIBRATION 51
- INSTRUMENT MAINTENANCE 53
- WARM-UP 55
- THEORY OF OPERATION 57
- 10.2. PNEUMATIC OPERATION 58
- 10.2.3. THE NAFION 59
- DRYER 59
- 10.3. ELECTRONIC OPERATION 61
- 10.3.2. THE RELAY PCA 62
- M300EU THEORY OF OPERATION 63
- 10.3.2.3. Status LED’s 64
- 10.3.3.1. A to D Conversion 64
- 10.3.3.2. Sensor Inputs 64
- TROUBLESHOOTING & REPAIR 67
- 05514 Rev A1 61 69
- (As Displayed) 71
- INDICATED FAILURE(S) 71
- 05514 Rev A1 63 71
- 11.3. GAS FLOW PROBLEMS 73
- OVEN HEATER K3 YES 74
- 11.5.2.1. A/D Functions 74
- A-2 05924 Rev K.6 78
- 05924 Rev K.6 A-3 79
- Æ iDAS Submenu 80
- Æ COMM and VARS Submenus 81
- Æ Hessen Protocol Submenu 82
- PASSDAS RNGE CLK MORE 83
- COMM VARS 83
- ZERO_LIMIT Ratio 1.15 0–5 84
- CO2_RANGE 86
- USER NOTES 94
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Teledyne 300EU
(86 strony)
(42 strony)Trust 17389 manuals
Owner’s manuals and user’s guides for Mice Trust 17389.
We providing 1 pdf manuals Trust 17389 for download free by document types: Datasheet
Komentarze do niniejszej Instrukcji