Teledyne 300EU Instrukcja Użytkownika Strona 40
- Strona / 94
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
M300EU OPERATING INSTRUCTIONS M300EU
Addendum to M300E/EM Manual P/N 04288
6.5. SETUP Æ MORE Æ VARS: INTERNAL VARIABLES
(VARS)
The information found in Section 6.12 of the M300E/EM Operators Manual (P/N 04288) is applicable to the
M300EU with the following exception(s):
• There is no STABIL_GAS variable available under the VARS menu of the M300EU.
• The following table supersedes Table 6-14 of the M300E/EM Operators Manual (P/N 04288).
Table 6-3: Test Functions Defined
NO. VARIABLE DESCRIPTION
ALLOWED
VALUES
0
DAS_HOLD_OFF
Changes the internal data acquisition system (iDAS) hold-off
time, which is the duration when data are not stored in the
iDAS because the software considers the data to be
questionable. That is the case during warm-up or just after
the instrument returns from one of its calibration modes to
SAMPLE mode. DAS_HOLD_OFF can be disabled entirely
in each iDAS channel.
Can be between 0.5
and 20 minutes
Default=15 min.
1
CONC_PRECISION
Allows the user to set the number of significant digits to the
right of the decimal point display of concentration and
stability values.
AUTO, 1, 2, 3, 4
Default=AUTO
2
DYN_ZERO
Dynamic zero automatically adjusts offset and slope of the
CO response when performing a zero point calibration
during an AutoCal (Chapter 7).
ON/OFF
3
DYN_SPAN
Dynamic span automatically adjusts slope and slope of the
CO response when performing a zero point calibration
during an AutoCal (Chapter 7).
Note that the DYN_ZERO and DYN_SPAN features are not
allowed for applications requiring EPA equivalency.
ON/OFF
4
CLOCK_ADJ
Adjusts the speed of the analyzer’s clock. Choose the +
sign if the clock is too slow, choose the - sign if the clock is
too fast.
-60 to +60 s/day
32 05831 Rev. 01
- MODEL 300EU 1
- SAFETY MESSAGES 3
- TABLE OF CONTENTS 5
- LIST OF FIGURES 6
- LIST OF TABLES 6
- LIST OF APPENDICES 7
- INTRODUCTION 9
- USER NOTES: 10
- WARRANTY 11
- GETTING STARTED 13
- 3.3. ELECTRICAL CONNECTIONS 14
- M300EU GETTING STARTED 15
- M300EU 16
- 3.4.2. WARNING MESSAGES 17
- 3.4.3. FUNCTIONAL CHECK 18
- 3.5. INITIAL CALIBRATION 19
- Scrubber 25
- SAMPLE CHAMBER 25
- 6.2. OPERATING MODES 28
- Mode Field 29
- 6.2.2. TEST FUNCTIONS 30
- RANGE CONFIGURATION 31
- FOR SINGLE RANGE MODE 33
- FOR DUAL RANGE MODE 34
- FOR AUTO RANGE MODE 35
- 05514 Rev A1 31 39
- DIAGNOSTICS FUNCTIONS 41
- AIO Configuration Submenu 43
- 6.7.4. HESSEN PROTOCOL 47
- CALIBRATION PROCEDURES 49
- EPA PROTOCOL CALIBRATION 51
- INSTRUMENT MAINTENANCE 53
- WARM-UP 55
- THEORY OF OPERATION 57
- 10.2. PNEUMATIC OPERATION 58
- 10.2.3. THE NAFION 59
- DRYER 59
- 10.3. ELECTRONIC OPERATION 61
- 10.3.2. THE RELAY PCA 62
- M300EU THEORY OF OPERATION 63
- 10.3.2.3. Status LED’s 64
- 10.3.3.1. A to D Conversion 64
- 10.3.3.2. Sensor Inputs 64
- TROUBLESHOOTING & REPAIR 67
- 05514 Rev A1 61 69
- (As Displayed) 71
- INDICATED FAILURE(S) 71
- 05514 Rev A1 63 71
- 11.3. GAS FLOW PROBLEMS 73
- OVEN HEATER K3 YES 74
- 11.5.2.1. A/D Functions 74
- A-2 05924 Rev K.6 78
- 05924 Rev K.6 A-3 79
- Æ iDAS Submenu 80
- Æ COMM and VARS Submenus 81
- Æ Hessen Protocol Submenu 82
- PASSDAS RNGE CLK MORE 83
- COMM VARS 83
- ZERO_LIMIT Ratio 1.15 0–5 84
- CO2_RANGE 86
- USER NOTES 94
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Teledyne 300EU
(86 strony)
(42 strony)Pfannenberg PF-RH-60000 Kit manuels
Manuels d'utilisation et guides de l'utilisateur pour Sécurité Pfannenberg PF-RH-60000 Kit.
Nous fournissons des manuels en pdf 1 Pfannenberg PF-RH-60000 Kit à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji